100vac input/ ? 15vdc (800ma) output non-isolated ac/dc converter bp5068-15 data sheet absolute maximum ratings input voltage output current esd endurance operating temperature range storage temperature range parameter symbol limits unit vi io vsurge topr tstg ?190 800 2 ?20 to +80 ?25 to +105 v mapk kv unit ?2 ?2 ?1 conditions v v ma v v vp-p % dc vi= ? 141v, io=800ma vi= ?141v vi= ?120 to ? 162v, io=800ma vi= ? 141v, io=0 to 800ma vi= ? 141v, io=800ma vi= ? 141v, io=800ma ? 1 maximum output current varies depending on ambient temperature ; please refer to derating curve. ? 2 please refer to load regulation, conversion efficiency. electrical characteristics input voltage range output voltage output current line regulation load regulation output ripple voltage power conversion efficiency parameter symbol typ. max. min. vi vo io vr vl vp ? 141 ? 15.0 ? 0.20 0.50 0.15 85 ? 162 ? 16.0 800 0.45 0.75 0.30 ? ? 120 ? 14.0 0 ? ? ? 80 load regulation load regulation 16.0 15.8 15.6 15.4 15.2 15.0 14.8 14.6 14.4 14.2 14.0 200 0 400 600 800 (ta=25 c , vi= ? 141v) output current io(ma) output voltage vo(v) conversion efficiency conversion efficiency 100 80 60 40 20 0 200 0 400 600 800 (ta=25 c , vi= ? 141v) output current io(ma) conversion efficiency (%) surface temperature increase surface temperature increase 40 35 30 25 20 15 10 5 0 200 0 400 600 800 (ta=25 c , vi= ? 141v) output current io(ma) temperature rising ?t( c) application circuit external component specifications fuse: fuse use a quick-acting fuse (2a) above 200v, 47 to 220 f ripple current 0.22arms above c1: input capacitor above 200v, 0.1 to 0.22 f use a film or ceramic capacitor. evaluate under actual operating conditions. c2: noise reduction capacitor above 35v, 330 to 1000 f, low impedance esr : 0.08 ? max. ripple current 1arms or above capacitor impedance affects the output ripple voltage. c3: output capacitor inductance : 470 h, rating current : above1.6a select components that do not easily get magnetically saturated at high temperature. l1: power inductor above 400v, current : above 3a fast recovery diode. please note that both the switching and efficiency characteristics of the module are affected by this diode. recommended products : 31df4 (nihon inter) d1: flywheel diode 1.0 to 2.2? , 1/4w determine the ideal value through actual testing. r1: noise reduction resistor use a rectifying diode with a peak reverse voltage of 400v or higher, an average rectification current of 1a or larger and a peak surge current of 20a or larger. when using a large capacitance input capacitor, select a component that is strong against inrush current during power up. full-wave rectification can be used. d2: rectifier diode a varistor is required to protect against lightning surges and static electricity. znr: varistor please verify operation and characteristics in the customer's circuit before actual usage. ensure that the load current does not exceed the maximum rating. bp5068-15 be sure to use fuse for safety. derating curve derating curve operation range 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 10 -30 -20 -10 20 4030 80706050 90 ambient temperature ta( c ) output current io(a) please note that pin no.12 side is input. ? 15v output input 470f/50v ac100v 50hz/60hz 0.1f c2 l1 470 h fuse 2a 1 12 810 7 5 3 + ? + ? 100 f/200v c1 znr 220v r1 2.2?1/4w d2 d1 1sr35-400a c3 pin no. 1 2 3 4 5 6 7 8 9 10 11 12 function output terminal vo( ?15v) skip coil connect skip coil connect skip common common skip n.c. skip input terminal vi( ?141vdc) dimensions (unit : mm) 21.5max. 4 1.0 34.5max. 2.54 11=27.94 1 3 5 7 8 10 12 0.5 0.1 p=2.54 0.2 1.3 0.2 3.25max mark side 11.3max. 7.35max. 3.95max. 0.25 0.05 c c + 100vac input/ ? 12vdc (800ma) output non-isolated ac/dc converter BP5068A data sheet absolute maximum ratings input voltage output current esd endurance operating temperature range storage temperature range parameter symbol limits unit vi io vsurge topr tstg ?190 850 2 ?20 to +80 ?25 to +105 v mapk kv c c unit ?2 ?2 ?2 ?2 ?1 conditions v v ma v v vp-p % dc(80 to 120vac) vi=? 141 v, io=800ma vi=? 141 v vi=?120 to ? 162v, io=800ma vi= ? 141v, io=0 to 800ma vi=? 141 v, io=800ma vi=? 141 v, io=800ma ? 1 maximum output current varies depending on ambient temperature ; please refer to derating curve. ? 2 please refer to load regulation, conversion efficiency. electrical characteristics input voltage range output voltage output current line regulation load regulation output ripple voltage power conversion efficiency parameter symbol typ. max. min. vi vo io vr vl vp ? 141 ? 12 ? 0.20 0.50 0.15 78 ? 162 ? 13 800 0.45 0.75 0.30 ? ?120 ? 11 0 ? ? ? 65 load regulation load regulation 13.0 12.5 12.0 11.5 11.0 200100 0 400300 600500 800700 (ta=25 c , vi= ? 141v) output current io(ma) output voltage -vo(v) conversion efficiency conversion efficiency 100 80 60 40 20 0 200 0 400 600 800700 500 300 100 (ta=25 c , vi= ? 141v) output current io(ma) conversion efficiency (%) surface temperature increase surface temperature increase 40 35 30 25 20 15 10 5 0 0 200 400 600 800 100 300 500 700 (ta=25 c , vi= ? 141v) output current io(ma) temperature rising ?t( c ) switching frequency switching frequency 50 40 30 20 10 0 200100 0 300 400 500 600 800700 (ta=25 c , vi= ?141v) output current io(ma) switching frequency fsw(khz) dimensions (unit : mm ) application circuit external component specifications fuse: fuse use a quick-acting fuse of 2a above 200v, 47 to 220 f ripple current 0.22arms or greater above 200v, 0.1 to 0.22 f use a film or ceramic capacitor. evaluate under actual operating conditions. c1: input capacitor c2: noise reduction capacitor above 25v, 330 to 1000 f, low impedance esr : 0.08 ? max. ripple current 1arms or greater capacitor impedance affects effects the output ripple voltage c3: output capacitor above 400v, current : above 3a fast recovery diode please note that both the switching and efficiency characteristics of the module are affected by this diode. recommended products : 31df4 (nihon inter) or ru30 (sanken) d1: flywheel diode inductance : 330 h, rating current : above 1.6a select components that do not easily get magnetically saturated at high temperature. l1: power inductor use a rectifying diode with a peak reverse voltage of 400v or higher, an average rectification current of 1a or larger and a peak surge current of 20a or larger. when using a large capacitance input capacitor, select a component that is strong against inrush current during power up. full-wave rectification can be used. d2: rectifier diode 1 to 2.2?, 1/4w reduce the noise terminal voltage. determine the ideal value through actual testing. r1: noise reduction resistor a varistor is required to protect against lightning surges and static electricity. znr: varistor pin no. 1 2 3 4 5 6 7 8 9 10 11 12 function output terminal vo( ?12v) skip coil connect skip coil connect skip common common skip nc skip input terminal vi( ?141vdc) please verify operation and characteristics in the customer's circuit before actual usage. ensure that the load current does not exceed the maximum rating. BP5068A be sure to use fuse for safety. 21.5max. 41.0 34.5max. 2.54?11=27.94 1 3 5 7 8 10 12 0.5 0.1 1.3 0.2 p=2.54 0.2 3.25max derating curve derating curve operation range 900 800 700 600 500 400 300 200 100 0 0 10 -30 -20 -10 20 4030 80706050 90 ambient temperature ta( c) output current io(ma) please note that pin no.12 side is input. ?12v output input 470f/50v ac100v 50hz/60hz 0.1f c2 d1 fuse 2a 1 12 8 710 5 3 + ? + ? 100 f/200v c1 znr 220v r1 l1 330h 2.2?1/4w d2 1sr35-400a c3 mark side 11.3max. 7.35max. 3.95max. 0.250.05 1/1 2010.01 - rev.a www.rohm.com ?2010 rohm co., ltd. all rights reserved.
r1010 a www.rohm.com ? 2010 rohm co., ltd. all rights reserved. notice rohm customer support system http://www.rohm.com/contact/ thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. notes no copying or reproduction of this document, in part or in whole, is permitted without the consent of rohm co.,ltd. the content specified herein is subject to change for improvement without notice. the content specified herein is for the purpose of introducing rohm's products (hereinafter "products"). if you wish to use any such product, please be sure to refer to the specifications, which can be obtained from rohm upon request. examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when designing circuits for mass production. great care was taken in ensuring the accuracy of the information specified in this document. however, should you incur any damage arising from any inaccuracy or misprint of such information, rohm shall bear no responsibility for such damage. the technical information specified herein is intended only to show the typical functions of and examples of application circuits for the products. rohm does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm and other parties. rohm shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. the products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, commu- nication devices, electronic appliances and amusement devices). the products specified in this document are not designed to be radiation tolerant. while rohm always makes efforts to enhance the quality and reliability of its products, a product may fail or malfunction for a variety of reasons. please be sure to implement in your equipment using the products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any product, such as derating, redunda ncy, fire control and fail-safe designs. rohm shall bear no responsibility whatsoever for your use of any product outside of the prescribed scope or not in accordance with the instruction manual. the products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospac e machinery, nuclear-reactor controller, fuel- controller or other safety device). rohm shall bear no responsibility in any way for use of any of the products for the above special purposes. if a product is intended to be used for any such special purpose, please contact a rohm sales representative before purchasing. if you intend to export or ship overseas any product or technology specified herein that may be controlled under the foreign exchange and the foreign trade law, you will be required to obtain a license or permit under the law.
|
